FitcamX Easy Power / Parking Mode Wiring - Newer Toyota Vehicles

$23.99

FitcamX Easy Power / Parking Mode Wiring - Newer Toyota Vehicles

Name: FitcamX Easy Power / Parking Mode Wiring - Newer Toyota Vehicles
Brand: StickerFab
SKU: fcx24LCGX550-HWK
Price: 23.99 USD
Availability: InStock

$23.99

Restores parking mode + full-time power — keeps your FitcamX or Revo dashcam recording impacts while you're parked
Plug-and-play into the factory OEM harness — taps the connector Toyota built for the OEM dashcam. Zero cutting, zero splicing
Fits 2024+ Land Cruiser, GX550, Tacoma & 2025+ 4Runner — vehicle-specific 5-pin fitment
Clean, hidden routing — tucks behind the map light assembly for a completely factory look
10-minute install — no tools beyond a trim pick; illustrated step-by-step guide included below
Requires a FitcamX or Revo dashcam — this is the power/parking-mode harness only

FitcamX Easy Power / Parking Mode Wiring for Newer Toyota Vehicles

A true plug-and-play power harness that unlocks parking mode on your FitcamX dashcam — no cutting, no add-a-fuse, no guesswork.

FitcamX Easy Power and Parking Mode wiring harness for 2024+ Toyota Land Cruiser, GX550, Tacoma and 2025+ 4Runner

Parking Mode, the Easy Way

Your FitcamX camera can capture impacts and break-in attempts while you're parked — but only if it has constant accessory power. This plug-and-play harness delivers exactly that. It plugs directly into the factory OEM cable Toyota originally designed for the OEM dashcam, so your camera gets clean, switched power without tapping the fuse box or splicing a single wire.

The result is genuine parking-mode protection (motion/impact triggered) with a wiring job that looks like it came from the factory.

FitcamX harness OEM 5-pin factory connector close-up

FitcamX Easy Power harness connectors - OEM plug and dashcam barrel connector

Built to Drop Straight In

One end matches the factory 5-pin connector hidden behind your map light assembly; the other powers your FitcamX or Revo dashcam. Because it uses the OEM circuit, there's nothing to program and nothing to cut — unplug the factory blank, plug in the harness, and route the cable.

Note: this is the power/parking-mode harness only. A FitcamX or Revo dashcam is required.

Step-by-Step Installation

FitcamX harness installation tutorial - removing the Toyota map light console and connecting to the OEM factory connector

⚙️ Install Takes About 10 Minutes

Remove the map light assembly by gently pulling the side closest to the windshield — it hinges down and swings out of the way. The factory 5-pin connector is usually along the sides of the opening, often taped up or partially covered. Unplug it, connect the harness, tuck the cable, and reinstall the assembly.

Connector location: 2024+ Land Cruiser / GX550 → passenger side (right). 2024+ Tacoma / 2025+ 4Runner → driver side (left).

FitcamX dashcam parking mode overview - StickerFab

FAQ

What vehicles does this fit?
2024+ Land Cruiser, 2024+ GX550, 2024+ Tacoma, and 2025+ 4Runner equipped with the factory OEM dashcam wiring connector.

Do I need to cut or splice any wires?
No. It's fully plug-and-play into the factory OEM harness — no cutting, no add-a-fuse taps.

Does this record continuously while parked?
It enables parking mode (motion/impact-triggered capture), not continuous 24/7 recording.

Does it include a camera?
No — this is the power/parking-mode wiring only. It requires a FitcamX or Revo dashcam.